VA-Series
Planetary Thread Rolling System for hi-tensile headed Fasteners.

**Planetary Thread Roller with a Closed Structure**
Models for thread rolling of automotive quality and
Hi-Tensile fasteners.

**New Extended-Die-Life System**
which is controlling the exact feed position on the cam and indexing the cam to have a fresh start point thus considerably increasing the die life.

The machine is equipped with Videx's "Controlled Introduction" system, for rolling Lap-Free threads on any material hardness. Other features include Hydraulic Clamp of the thread rolling dies & Quick Set-Up features. Thread range M-6 to M-16. Production speed up to 640 PPM.

Come See The New Extended-Die-Life System
Running production at:
WIRE 2012
Düsseldorf, March 26-30, Booth 15A46

Our systems offer the following:

• Diameter range of NC 6 to 1.25”.
• General commercial thread rolling.
  For use on Fasteners up to 22 Rc.
• Dual Spindle machines.
  Offering many different solution such as.
• Thread rolling two different thread types on one fastener in one pass of the machine.
• Rolling straightening after heat before thread rolling in one pass of the machine.
• Thread rolling above and below a collar.
• Large Headed Fasteners example “ T” bolts.
• Nail Rollers are available 5,000 ppm.

Extra deep die pockets for long Fasteners

VC-Series
Absolute World Leader in Straighten & Cut Machines
Specializing in Hi tensile, hot rolled, exotic materials and cold drawn wires.

• Diameter Range: 1/8” to 1.25”
• Offering flying shear and Patented mechanical servo cutoffs.
• Very Accurate Length Control ±0.004".
• No clutch to maintain.
• High Speed short cuts to long bars in one machine.
• Integrated single or double end chamfering fully automatically.
• Complete length and diameter change over in minutes.
• Lowest tooling cost on the market.
• Extremely high straightness capabilities.
• Straighten and Cut Ribbed Wire.

VAS-Series
From wire coil to bent bolts and straight studs.
Straighten cut material to length and perform the following options.

• Thread Rolling Single or Double End.
• Roll or cut chamfer.
• Bend into u-bolts, anchor bolts, j bolts and eye bolts.
• Fully Threaded studs.
• Extruding or heading optional.
• Secondary Operations, cross drilling, end drilling, flux ball insertion, stamping or marking
• Multiple turning operations.
• Also offering VS-series with all of the options as above just a hand feed machine for precut blanks.

VIC-Series
Impact cutters or Bar Shears
Crop straight bars to precise lengths with a square cut of face.

• Cut off length repeatability ±0.003” by hitting a positive stop.
• Bar is supported during shearing, assuring square cut off face.
• Works with Videx bar feeder or with any other bar feeder.
• Compact Design.
• Diameter range .250” to 2.5” Larger upon request.
• Optional Computer Console for entering bar lengths.
• This machine can be equipped with a thread roller or chamfering units.
• Quick Change over on diameters and lengths.

VCM-Series / VCS-Series
Chamfering machine for round bars
Free standing chamfering unit for single or double end chamfering.

• Diameter range .187” to 3”.
• Unlimited lengths example 4” to 30’.
• Stamping on single or double end.
• Attached to any Straighten and Cut machine.
• Adjustable heights.
• Multiple Turning Operation Optional.
• Can be used for bar stud or precut fastener blanks.
• Positive stop in chamfering head.
• Can perform two different operations on each end.
• Change Tooling covering entire range of machine.

VEM-Series
Hand feed or Fully automatic extruding to pitch diameter

• Hydraulic Extrusion Machine.
• Hand feed or Magazine feed.
• Multiple Extrusion possible.
• Faster and cleaner than turning blanks.
• Diameter Range .2500” to 3” larger upon request.
• Prepare blanks for thread rolling not thread cutting.
• 5 times faster than turning blanks.

VRH-Series
Multiple station heading operations

• Hand or Magazine Feed or fully Automatic from coil.
• Open Die rod with 1-3 stations.
• 50-300 tons for heading tonnage.
• Unlimited Lengths.
• Can head bent parts.
• Secondary Operation can be integrated.
• Offering solid die heading operation cold, warm or hot up to 500 tons.
• Quick change tooling available.
• Ideal for job shop applications.

VBH-Series
Bending Machines With A Slide-Die
Free standing bending units for job shop applications

• Fully Mechanical Bender.
• Magazine feed for precut blanks.
• For U-bolts, anchor bolts, j bolts, eye bolts.
• Quick change sliding bending for fast change overs.
• Diameter range .160” to 1” diameter larger upon request.
• Self-centering bending die.